نماد اعتماد و اعتبار در ایران
ارائه انواع راهکارهای مختلف برای هر محیطی
بی رقیب در کیفیت بی نظیر در اجرا
راهنمای نصب راهبند بلانکو مدل Cyble

راهنمای نصب راهبند بلانکو مدل Cyble

FAST INSTALLATION MANUAL

cyble-00001

 

WARNING

  • NEVER let children operate or play with barrier control. Controller MUST be installed at least 1.5m above the ground.
  • PEDESTRIANS SHOULD NOT CROSS THE PATH OF THE MOVING BARRIER.
  • Automatic boom barrier is designed for vehicles ONLY. Pedestrians MUST use separate entrance.
  • Installation and maintenance MUST be executed by qualified service person. Keep boom barriers properly maintained.
  • Ground wire and current breaker MUST be connected.
  • Power MUST be cut off when performing installation or maintenance.
  • When power outage, power MUST be cut off before using the manual release under the motor to open the barrier.
  • ONLY operate when the boom barrier is in sight.
  • NEVER perform operating or setting without the boom installed. This WILL result in severe injury.
  • NEVER dismount the boom when barrier is at close status with spring attached. This WILL result in sever injury, even death.
  • DO NOT replace the original wire.
  1. Direction Definition and Main Components of the Machine

cyble-00002

C.Main Components of the Motor

cyble-00003

  1. Features
  • Remote control is
  • During power outage, product can be manual
  • Control board contains various ports for parking lot management system, infrared sensor, radar,
  • Product contains multiple limit protection functions to keep a long life
  1. Specification

Rated Power

240W

 

 

Power Supply

220V±10% 50/60Hz

110V±10% 50/60Hz

Working Temperature

-35℃~+50℃

Max. Boom Length with

Operating Speed

 

6m (6s)

4m (3s)

3m (1.5s)

Installation

4.1 Cabinet Installation

  • Open the Cabinet door and take out the attachment pack. Place the Cabinet at desired position.
  • Place Fixed Bars on the bottom of the Cabinet inside.
  • Mark out the boreholes for Expansion Bolts (Fig. 3: L and W) according to the Fixed Bars. Move away the cabinet.
  • Use an electric drill with 21mm to drill the boreholes. The depth of the boreholes should be 110
  • ~ 120mm. Place the Expansion Bolts.
  • Move the cabinet back to the desired position and place the Fixed Bars on the bottom of the cainet inside.
  • Tighten the Expansion Bolts.

cyble-00004

4.1  Boom Installation

Loosen the Screws and move the spring(s) away from the  Spring Support. (Fig. 4)

cyble-00005

Using the Manual Release Handle to steer the Boom holder to horizontal

cyble-00006

Install the boom and Outer boom holder according to Fig.

cyble-00007

  • Fix the Boom Support on the ground. Adjust the height as the  Rubber pad touches the boom when the boom is at horizontal

cyble-00008

  1. Setting Springs’ Balance with Boom Weight

Attention: The springs are set to be balanced in factory. DO NOT change the boom length or weight if it is not necessary. If the boom length or weight must be changed (e.g.: adding a Stop Sign on the boom), the balance must be adjusted by a qualified service person.

5.1  Spring Quantity and

Boom Length

Quantity of spring

Spring Size

x≤3m

1

Φ4

3m<x≤4m

1

Φ5

4m<x≤5m2

Φ5

5m<x≤6m2

Φ5+Φ6

  • Spring Adjustment

Remove the screws on the Cabinet hat, and remove the

cyble-00009

Based on the weight added or subtracted on the boom, adjust the Spring Tighten the nut clockwise if the weight increased. Loosen the nut counter-clockwise if the weight decreased. When adjusting, all nuts should be turned at the same cycles, in order to avoid the unevenly distributed loads.

cyble-000010

Loosen Lower Linkage nut and take off the Upper Linkage nut. Turn  Manual Release towards Open Status to pull out Adjusting Insert. Turn the Manual Release towards Close Status, and stop when the boom is between 30° to 60°. If the boom moves towards Open Status, the Spring Nut should be loosened or reduce the number of If the boom moves toward Close Status, the Spring Nut should be tightened or increase the number of springs.

Tighten the Upper and Lower Linkage nuts after the adjustment.

cyble-000011

 

  1. Operating Instructions
  • Use remote controller to operate Automatic Boom
  • During power outage, turn the Manual Release towards Open Status to open the Automatic Boom Barrier.

cyble-000012

cyble-000013

cyble-000014

  1. Limit Adjusting

Attention: Limits are set well in factory. Any change made on boom length, weight, spring force, etc. may cause deviation on the limits. To adjust the limits, please follow steps below.

8.1  Optical Counter Disk

cyble-000015

8.1  Open, Close Limits

For easy understanding,we assume the value of “P1 ” and “ P2” with “ 6” on the Control Board means the boom at vertical and horizontal position. Fig.14 shows the boom status with the displaying value on the Control Board.

cyble 000016

8.1  Limits resetting

Before adjusting, open and close the boom once to see whether the boom is vertical and hori- zontal to the ground. If so, no adjustment is needed. Otherwise, follow the steps below to set the value of P1 and P2.

Warning!     Resetting should be operated by a qualified person.

cyble 000017

  1. Function Parameters

9.1  Function Definition

F0

Factory Setting (Caution!)

F1

Open Limit Micro-adjustment(for digital encoder)

F2

Close Limit Micro-adjustment(for digital encoder)

 

F3

Auto-Close Timer (s).    Max.: 99s. Default: 00 (Means auto-close function disabled)

F4

00: Normal Mode (Default).      01: Counting Mode.
F5

00: Normal Mode (Default).      01: Stay OPEN.

 

F6

01: Stay Light-on when open to limit(Default). 00: Light out when open to limit

F7

01: Encoder Value (Default)      00: Operation Status.

F8

Signal Input Mode.    00: N.O. (Default).     01: N.C.

F9

Alarm or Light.    01: Light (Default)      00: Alarm.

 

  • Timer Definition

F0

Year

F1

Month

F2

Day

F3

Hour

F4

Minute

F5

Second

F6

Light-on Hour. Default: 18
F7

Light-on Minute. Default: 00

F8

Light-out Hour. Default: 06

F9

Light-out Minute. Default: 00

 

Parametors of Function and Time Resetting

cyble-000018

  1. Transmitter (Remote control) setting

  • Transmitter’s code setting

 Press “LEARN butTON”, the “LEARN LED” light on, then, press and hold the button which you choose on the transmitter till the “LEARN LED” flashes and goes out, now, the transmitter is coded. Other transmitters can be coded as this way.

10.2     Erasing the transmitter’s code

Press” LEARN BUTTON” and hold on to make the “LEARN LED” light on and till go out. Now, all codes of transmitters which had been learnt are cleared.

  1. Error Codes
CodeMeaningSolution
Err1Optical Counter LimitsCheck the Optical Counter Limits wires
 

Err2

 

Motor Nonstop Running Over Limits

1.Check the Optical Counter Limits Connecting 2.Check the Mechanical System
 

Err3

 

Motor Locked Rotor

1.Check the Mechanical System 2.Check Motor Wires Connectors
Err7Photocell is TriggeredRemove the Object that Blocks the Photo Beam
Err8Air Wave Sensor TriggeredRemove the Object that Block the Air Wave
  1. Trouble Shooting
TroublePossible ReasonSolution
 

 

 

 

 

 

 

Power On, operate remote controller(transmitter), but no reaction.

 

Fuse blowout.

Check fuse inside control box and power supply.
No battery or dead battery in remote controller(transmitter). 

Change the batteries in transmitter.

 

 

Frequency interference.

 

Press “Open” or “Close” on the Main Board to teso if needed , connet a wired controller.

 

External protectors’ circuit malfunctioned or at working status.

 

Check the External Protectors or change them if need.

Optical counter malfunction.Change Optical counter.
Control board malfunction.Change control board.
 

 

 

Motor is functional but the boom doesn’t work.

 

Boom starts at middle position.

Use manual release to set the boom at Open status orClose status, then use controller to start again.
Spring force is not balance.Readjust the balance.
 

Low power voltage.

Check if the input power is at proper range.
 

Boom does not reach correct position when opening and closing.

Incorrect Linkage adjustment.Refer to Fig.15 (See page 10).
Incorrect Limits setting.Reset.
 

Boom shakes at Open Limit and Close Limit.

 

The Lock Flat Key between Boom Main Shaft and Boom Holder is loose.

 

Change the Lock Flat Key.

دانلود فایل راهنمای نصب راهبند بلانکو مدل cybel:

راهنمای نصب سریع

راهنمای نصب

برای آشنایی با دیگر محصولات از جمله درب اتوماتیک، درب پارکینگ، درب شیشه ای، کرکره برقی، راهبند و غیره کلیک کنید.

 

نام فایل: راهنمای نصب راهبند بلانکو مدل Cyble
سایز: 1.960 MB
فرمت: pdf
دانلود فایل